Course: LV_MV_HV Circuit Breakers (Switchgear): Inspection, Maintenance, Design, Repair & Troubleshooting

Course Outline

Day One

 General Introduction

•     Electrical engineering basic concepts
•    Three phase review and per unit
•    Voltage levels
•   One line and three line diagram
•    Generation system layout
•    Transmission system layout
•    Substation system layout
•    Distribution system layout

 Industrial Switchgears

•     Fuses
•     Auto-reclosers
•    Automatic sectionalizer
•     Circuit Breakers
•    Isolator switches
•    Load switches
•    Relays
•    Current transformers
•    Voltage transformers

Day Two

 CB Design Specification Based on Short Circuit Current Level

•    Per unit system
•   Faults on power systems
•    Transient phenomena in power system.
•    Symmetrical component analysis of three phase network
•     Network connection for various fault types
•    Current and voltage distribution in system due to a fault
•     Effect of system on zero sequence quantities
•    Computer programs based short circuit calculation.

 CB Design Specification Based on Arc Phenomena and Circuit Interruption

•    Arc phenomena
•   Maintenance of the Arc
•   Properties of Arc
•    Arc Interruption theory
•   Circuit Breaker Rating
•   Circuit constants and circuit conditions
•   Conditions of severity
•    Restriking voltage transient
•    Class A ultra fast transients
•    Class B system transients
•    Class C low transients
•    Transmission line transient
•    Switching transients
•    Duties of Switchgear

Day Three

 LV Circuit Breakers

•    Low voltage molded case current limiting circuit breakers
•    Low voltage molded case circuit breakers with high breaking capacity
•    Insulated case circuit breakers
•     Low voltage air circuit breakers
•    Low voltage circuit breakers specification

 Modern MV and HV Vacuum CB

•     Introduction
•    Advantages of vacuum interruption
•    Vacuum contactors and interrupters
•    The vacuum medium
•    The vacuum arc
•    Vacuum arc stability
•   Vacuum break down
•   Vacuum switch construction
•    Applications of vacuum circuit breakers

 Modern MV and HV SF6 CB Introduction

•    Basic Features of SF6 Breakers
•    Dielectric properties of SF6
•     Quenching properties of SF6
•    Construction of SF6 breaker
•     SF6 CB types
•    Puffer type SF6 breakers
•    Double Pressure System
•     Single Pressure Puffer-Piston System
•   Single Pressure Self Blast System
•     Improvement in SF6 Breakers for HV

Day Four

 Other Type of Circuit Breakers

•  Air Circuit Breakers
  •    Method of increasing arc resistance
  •    Plan break type
  •    Magnetic blow out type
  •    Arc splitter type
  •    Application
  •    Construction and operation
  •    Axial air CB
  •   Blast air CB
•  Oil Circuit Breakers
  •     Arc rupture under oil
  •    Advantages of oil
  •    Disadvantages of oil
  •     Plan break oil circuit breakers
  •    Arc control circuit oil breakers
  •    Minimum oil circuit breakers
  •    Construction and operation
•  Dc Circuit Breakers
  •    Construction
  •   Methods of interruption
  •    Application

Day Five

 Circuit Breaker Inspection, Maintenance and Services

•    Inspection
•     General inspection technical procedure
•     Daily inspection of circuit breakers
•     Monthly inspection of circuit breakers
•    Annual inspection of circuit breakers
•    Disassembly
•    Cleaning
•    Tightening
•    Lubrication
•    Equipments used in testing
•    Testing procedure
•     Direct testing
•    Contact resistance test.
•     Insulation resistance test
•    Test report
•     Indirect testing
•    One hour Video, HV CB Maintenance and Repair)

 Circuit Breakers Control, Protection and Testing

•   Switchgears control devices and wiring
•    Switchgears protection devices and wiring
•    Testing Classification
•    Testing laboratories
•    Description of a simple testing station

 CB Troubleshooting

• Low insulation Resistance (below 2000 Mega-ohms) between a) Phase terminal and earthed frame, with breaker closed b) Phase terminals of a pole.
• Resistance between Termi¬nals of Pole too high (above 100 microhms) (15 micro-ohm per joint) contact
• Unequal contact Wipe and Travel in 3-pole Measured from top surface of inter¬rupter flange and the contact lip by a simple rod with a) breaker open and b) breaker closed
• One of the pole docs not close.
• Breaker operation too Slow During opening timing from trip command to contact separation instant too large (60 ms instead of say 40 ms)

The Scandinavian Academy for Training and Development adopts the latest scientific and professional methodologies in training and human resource development, aiming to enhance the efficiency of individuals and organizations. Training programs are delivered through a comprehensive approach that includes:

• Theoretical lectures supported by PowerPoint presentations and visual materials (videos and short films).
• Scientific evaluation of participants before and after the program to measure progress and knowledge acquisition.
• Brainstorming sessions and practical role-playing to simulate real-life scenarios.
• Case studies tailored to align with the training content and participants work nature.
• Assessment tests conducted at the end of the program to evaluate the achievement of training objectives.

Each participant receives the training material (both theoretical and practical) in printed form and saved on a CD or flash drive. Detailed reports, including attendance records, final results, and overall program evaluations, are also provided.

Training materials are prepared professionally by a team of experts and specialists in various fields. At the end of the program, participants are awarded a professional attendance certificate, signed and accredited by the Scandinavian Academy for Training and Development.

Program Timings:

• 9:00 AM to 2:00 PM in Arab cities.
• 10:00 AM to 3:00 PM in European and Asian cities.

The program includes:

• A daily buffet provided during the sessions to ensure participants comfort.

Course Description

This workshop is designed to update participants with the latest development of Circuit Breakers and to present some of the more common and updated aspects of low, medium and high voltage switchgear maintenance. It must be understood that there is an incredible variety of equipment used on low, medium and high voltage switchgear today. Switchgears play an important role in the distribution and control of electrical power in manufacturing or power plant and in a utility distribution system. Negligent maintenance practices can lead to power system inefficiency and loss of system reliability.

Course Objective

This course is designed to enable participants to:

• List the voltage convention classifications used in this course.
•  Describe switchgear construction.
•  Describe a ground fault relay system.
•  Describe the three basic types of low and medium voltage circuit breaker contacts.
•  Describe the molded case circuit breaker.

Who Should attend?

This course is recommended for skilled trades, supervisors, and anyone involved in the maintenance of industrial power circuit breakers

The Scandinavian Academy for Training and Development is committed to hosting all training programs in dedicated and well-equipped hotel facilities specifically designed for conducting and delivering training sessions, unless explicitly stated otherwise on our website. Participants will be notified of the program venue within 7 to 21 days prior to the programs start date, based on the Academys assessment and the programs circumstances. The Scandinavian Academy for Training and Development emphasizes that it holds no responsibility for any force majeure events that may prevent the program from being held at the designated venue. Nevertheless, the Scandinavian Academy for Training and Development will make every effort to provide suitable alternatives and extend the necessary support to participants in the event of a venue change due to unforeseen circumstances.